Overzicht van de meetwaarde blokken voor een 3.0 TDI A4 2008 (klopte voor mijn A6 2005 voor zover ik nu heb kunnen ontdekken.)

Ben het tegen gekomen op een Engels forum:
http://www.vwaudiforum.co.uk/forum/s...urement-blocks



Display groups for 3.0 L TDI CR as at 22.01. 2008
Audi A4

001 Quantity adjustment
1) Engine speed
At idle: 720 ... 820 rpm
2) Injection quantity
At idle: 4 ... 10,5 mg/stroke
3) Rail pressure actual
Check values with measured value block 022
4) Coolant temperature
Warmed-up: 70 ... 110 °C

002 Idling speed
1) Engine speed
At idle: 720 ... 820 rpm
2) Accelerator pedal position
At idle: 0 %
At full throttle: 100%
3) Pedal switch settings
X X 1 Idling speed switch ON
X 1 X Kickdown switch ON
1 X X Idling speed increased
4) Coolant temperature
Warmed-up: 70 ... 110 °C

003 Exhaust gas recirculation
1) Engine speed
At idle: 720 ... 820 rpm
2) Specified intake air mass
[mg/stroke]
3) Actual air mass
[mg/stroke]
4) EGR valve activation
[%]

004 Main injection
1) Engine speed
At idle: 720 ... 820 rpm
2) Main injection, start of activation
[°CA]
3) Main injection, duration of activation
[ms]
4) Rail pressure actual
Check values with measured value block 022

005 Starting conditions
Stored from last engine start
1) Engine speed
[rpm]
2) Starting injection quantity
[mg/stroke]
3) Start synchronisation
000 Basic initialisation
001 Reset counter
002 Engine standstill or fault
003 Transitional states
004 Plausibility check phase
005 Plausibility check phase
006 Plausibility check phase
008 Plausibility check phase
016 Phase definition
032 Synchronisation phase
033 System positioning
048 Calculation sequences activated --> Start OK
064 System waiting for engine standstill
128 Dynamic plausibility check
4) Coolant temperature
[°C]

006 Cruise control system CCS
1) Vehicle speed
CCS activatable: above 35 km/h
2) CCS status
X X X X X X X 1 Brake light switch pressed
X X X X X X 1 X Brake pedal switch pressed
X X X X X 1 X X Clutch pedal switch pressed
X X X X 1 X X X CCS enabled
X X X 1 X X X X ACC enabled
X X 0 X X X X X Main switch
0 0 X X X X X X ACC/CCS mode inactive
1 0 X X X X X X State overspill
0 1 X X X X X X ACC/CCS in control range
1 1 X X X X X X ACC not enabled
3) CCS target speed
[km/h]
4) CCS switch settings
X - X X X X X 1 Locked ON
X - X X X X 1 X Touched OFF
X - X X X 1 X X Touch-Down, reduce
X - X X 1 X X X Touch-Up, increase
X - X 1 X X X X Set
X - 1 X X X X X Resume
1 - X X X X X X Locked ON from hardware

007 Temperature senders
1) Fuel temperature
to 70 °C
2) Oil temperature
Warmed-up: 70 ... 110 °C
3) Intake air temperature
to 75 °C
4) Coolant temperature
Warmed-up: 70 ... 110 °C

008 Limiting torques
1) Engine speed
[rpm]
2) Internal torque
[Nm]
3) Torque limitation
[Nm]
4) Smoke limitation
[Nm]

009 Limiting torques
1) Engine torque specification
[Nm] Driver input via accelerator pedal
2) Limiting torque gearbox control unit
[Nm] during gearshifting
3) Limiting torque MSR
[Nm] of engine drag torque control
4) Limiting torque TCS
[Nm] of traction control

010 Air quantities
1) Actual air mass
At idle: 210 ... 280 mg/stroke
At full throttle: > 1050 mg/stroke
At ambient air pressure 970 ... 1020 mbar
2) Ambient air pressure
[mbar]
3) Actual charge pressure
At idle: 950 ... 1080 mbar
At full throttle: > 2150 mbar
At ambient air pressure 970 ... 1020 mbar
4) Accelerator pedal position
[%]
- With exhaust gas recirculation switched off, e.g. due to
high intake air temperature the air mass at idle may be increased
In this case press the accelerator in short bursts and check
whether the air mass then decreases.
- Additionally check air mass via basic setting of EGR
and turbocharger basic setting.

011 Charge pressure control
1) Engine speed
[rpm]
2) Specified charge pressure
[mbar]
3) Actual charge pressure
At idle: 950 ... 1080 mbar
At full throttle: > 2150 mbar
At ambient air pressure 970 ... 1020 mbar
4) Charge pressure adjuster specification
[%]

012 Preheating system
1) Preheating system status
0 0 0 0 0 0 0 0 Waiting for coolant temperature
0 0 0 0 0 0 0 1 Waiting for start request
0 0 0 1 0 0 0 0 Glow period
0 1 0 1 0 0 0 0 No glow
1 0 1 1 0 0 0 0 After-glow
1 1 0 0 0 0 0 0 No start glow
1 1 1 1 0 0 0 0 Intermediate glow
0 0 1 1 0 0 0 0 Readiness glow
0 1 1 1 0 0 0 0 Start glow
1 0 1 1 0 0 0 1 Waiting for after-glow
1 1 0 1 0 0 0 0 No after-glow
1 1 1 1 0 0 0 1 Waiting for intermediate glow
1 1 1 1 1 1 1 1 No glow
2) Glow period
[s]
3)Vehicle voltage
[V]
4) Coolant temperature
[°C]

013 Smooth running control
1)Cyl. 1 Injection quantity variation
[mg/stroke]
2)Cyl. 2 Injection quantity variation
[mg/stroke]
3)Cyl. 3 Injection quantity variation
[mg/stroke]
4) Vacant
Permissible values at idle: +- 2,99 mg/stroke
A If the permissible tolerance is exceeded
first check injector IQA-IVA adaption values

014 Smooth running control
1)Cyl. 4 Injection quantity variation
[mg/stroke]
2)Cyl. 5 Injection quantity variation
[mg/stroke]
3)Cyl. 6 Injection quantity variation
[mg/stroke]
4) Vacant
Permissible values at idle: +- 2,99 mg/stroke
A If the permissible tolerance is exceeded
first check injector IQA-IVA adaption values

015 Fuel consumption
1) Engine speed
[rpm]
2) Injection quantity
[mg/stroke]
3) Fuel consumption
[ltr/h]
4) Engine torque specification
[Nm] Driver input via accelerator pedal

016 Additional heater
1) Vacant
2) Additional heater shut-off conditions
0 0 0 0 0 0 0 0 No shut-off condition
0 0 0 0 0 0 0 1 Coolant temperature
adequate
0 0 0 0 0 0 1 0 Alternator load signal error
0 0 0 0 0 1 0 0 Battery voltage too high
0 0 0 0 1 0 0 0 Engine speed too low
0 0 0 1 0 0 0 0 Start delay active
0 0 1 0 0 0 0 0 Water temperature sensor, air temperature
sensor or output stage defective
0 1 0 0 0 0 0 0 Operating switch (not active)
1 0 0 0 0 0 0 0 Intake manifold temperature adequate
3) Additional heater relay activation
0 0 Relay not activated
0 1 Low heat output relay
1 0 High heat output relay
1 1 Both relay contacts active
4) Vehicle voltage (to 11.2005)
[V]
4) Alternator DF signal (from 11.2005)
[%] Alternator load

017 Readiness code
1) EOBD data A
X 0 0 0 0 0 0 0 No fault messages stored in engine control unit

0 X X X X X X X Emissions warning lamp (MIL) OFF
1 X X X X X X X Emissions warning lamp (MIL) ON
2) EOBD data B
- X X - - X X 1 Misfire monitoring activated
- X X - - X X 1 Misfire monitoring activated
- X X - - 1 X X Complete system monitoring activated
- X 0 - - X X X EOBD test fuel system completed with OK

- 0 X - - X X X EOBD test overall system completed with OK

3) EOBD data C
X X X X - X X 1 Catalytic converter monitoring activated
X X X X - X 1 X Catalytic converter hot monitoring activated
X X X X - 1 X X Evaporation system monitoring activated
X X X 1 - X X X Air conditioner coolant monitoring activated
X X 1 X - X X X Lambda probe monitoring activated
X 1 X X - X X X Lambda probe heating monitoring activated
1 X X X - X X X EGR monitoring activated
4) EOBD data D
0 - - - - - - X EOBD test EGR completed with OK


018 Throttle valve
Only for throttle valves with 4 cables on connector
If 5 cables, see measured value block 038
1) Engine speed
[rpm]
2) Throttle valve activation
[%]
3) Intake air temperature
[°C]
4) Actual air mass
[mg/stroke]

019 Fan activation
1) Coolant temperature
[°C]
2) Air conditioner fan activation
[%]
3) Radiator fan 1 activation
[%]
4) Radiator fan 2 activation
[%]

020 AC compressor
1) Ambient temperature
[°C]
2) Vacant
3) AC compressor shut-off status 1
X X X X X X X 1 Vehicle starting off
X X X X X X 1 X Shut-off due to starting off state
X X X X X 1 X X Vehicle acceleration
status
X X X X 1 X X X Shut-off due to acceleration
X X X 1 X X X X Shut-off due to starting
X X 1 X X X X X System fault detected
X 1 X X X X X X Shut-off due to system fault
1 X X X X X X X Shut-off due to inadequate idling
speed
4) AC compressor shut-off status 2
X X X X X X X 1 Shut-off due to excessive coolant temperature

X X X X X X 1 X Shut-off by gearbox control unit
X X X X X 1 X X Shut-off by ABS/ESP control unit
X X X X 1 X X X Shut-off due to refrigerant pressure or
ambient temperature
X X X 1 X X X X Power reduction due to overheating
X X 1 X X X X X Shut-off due to fault in a radiator fan
X 1 X X X X X X Shut-off due to fault in both radiator fans
1 X X X X X X X Minimum on-time

022 Rail pressure control
1) Engine speed
At idle: 720 ... 820 rpm
2) Specified rail pressure
[bar]
3) Rail pressure actual
[bar]
4) Pressure regulating valve activation
At idle: 15 ... 30 %
- Values for warmed-up engine
- Permissible difference between specified and actual value at
Idle: maximum +-20 bar

023 Rail quantity control
1) Engine speed
At idle: 720 ... 820 rpm
2) Specified rail pressure
Check values with measured value block 022
3) Rail pressure actual
Check values with measured value block 022
4) Quantity adjuster valve activation
At idle: 35 ... 48 %
Values for warmed-up engine

024 Pre-injection 1
1) Engine speed
[rpm]
2) Pre-injection 1 start of activation
[°CA]
3) Pre-injection 1 duration of activation
[ms]
4) Rail pressure actual
Check values with measured value block 022

025 Pre-injection 2
1) Engine speed
[rpm]
2) Pre-injection 2 start of activation
[°CA]
3) Pre-injection 2 duration of activation
[ms]
4) Rail pressure actual
Check values with measured value block 022

026 Post-injection 1
1) Engine speed
[rpm]
2) Post-injection 1 start of activation
[°CA]
3) Post-injection 1 duration of activation
[ms]
4) Rail pressure actual
Check values with measured value block 022

029 Adaptive cruise control ACC
1) ACC specification adjustment
001 Specification adjustment free-wheeling
002 Specification adjustment ON
003 Specification adjustment OFF
2) ACC status
X X X X X X 0 0 ACC inactive
X X X X X X 0 1 ACC active
X X X X X X 1 0 ACC passive
X X X X X X 1 1 ACC initialisation
X X X X X 0 X X No neutral value
X X X X X 1 X X Neutral value
X X 0 X X X X X Not permitted
X X 1 X X X X X Permitted
3) Vehicle speed
[km/h]
4) Vacant

030 Accelerator pedal position
1) Accelerator pedal sender 1
[V]
2) Accelerator pedal sender 2
[V]
3)Switch settings
X X 1 Idling speed switch ON
X 1 X Kickdown switch ON
1 X X Idling speed increased
4) Accelerator pedal position
[%]

032 Camshaft edges (from 11.2005)
1) Engine speed
[rpm]
2) Start synchronisation
000 Basic initialisation
001 Reset counter
002 Engine standstill or fault
003 Transitional states
004 Plausibility check phase
005 Plausibility check phase
006 Plausibility check phase
008 Plausibility check phase
016 Phase definition
032 Synchronisation phase
033 System positioning
048 Calculation sequences activated --> Start OK
064 System waiting for engine standstill
128 Dynamic plausibility check
3) Camshaft edge 1
[°CA]
4) Camshaft edge 2
[°CA]

034 Charge pressure control
1) Engine speed
At idle: 720 ... 820 rpm
2) Charge pressure adjuster specification
At idle: 20 ... 80 %
3) Charge pressure adjuster actual value
At idle: 19 ... 81 %
4) Actual charge pressure
[mbar]

035 Temperature protection
1) Engine speed
At idle: 720 ... 820 rpm
2) Exhaust gas temperature before turbocharger
At idle: 140 ... 310 °C (with radiator fluid > 75 °C)
At full throttle: 540 ... 830 °C
3) Exhaust gas governing factor
At idle: 99 ... 101 % or 0.99 ... 1,01
4) Overall governing factor
At idle: 99 ... 101 % or 0.99 ... 1,01

036 Intake manifold flap bank 1
1) Engine speed
At idle: 720 ... 820 rpm
2) Intake manifold flaps bank 1 specification
At idle: 19 ... 81 %
3) Intake manifold flaps bank 1 actual value
At idle: 19 ... 81 %
4) Actual air mass
[mg/stroke]
Permissible difference between specified and actual value at
Idle: maximum +/- 2 %

037 Intake manifold flap bank 2
1) Engine speed
At idle: 720 ... 820 rpm
2) Intake manifold flaps bank 2 specification
At idle: 19 ... 81 %
3) Intake manifold flaps bank 2 actual value
At idle: 19 ... 81 %
4) Actual air mass
[mg/stroke]
Permissible difference between specified and actual value at
Idle: maximum +/- 2 %

038 Throttle valve
Only for throttle valves with 5 cables on connector
If 4 cables, see measured value block 018
1) Engine speed
[rpm]
2) Throttle valve activation control motor
[%]
3) Throttle valve specification
[%]
4) Throttle valve actual
[%]

040 Lambda probe
1) Probe calibration value internal resistance
[%] to 11.2005
[Ohm] from 11.2005
2) Oxygen signal
[V]
3) Oxygen concentration
[%]
4) Oxygen signal calibration status
0 inactive
1 active

041 Lambda probe
1) Air mass throughput
[-]
2) Probe heater activation
[%]
3) Probe temperature signal
[V]
4) Lambda signal
[-]

042 Lambda probe
1) Air mass throughput
[-]
2) Ambient temperature
[°C]
3) Lambda probe pressure
[mbar]
4) Oxygen concentration
[mV]

043 Lambda probe
1) Engine speed
[rpm]
2) Exhaust gas temperature at lambda probe
[°C]
3) Exhaust gas counterpressure
[mbar]
4) Exhaust gas mass flow
[-]

044 Lambda probe
1) Engine speed
[rpm]
2) Lambda probe electronics
X X X X X X X 1 Full throttle regulator on/off
X X X X X X 1 X Full throttle
X X X X X 1 X X Control deviation negative, i.e. mixture too rich
X X X X 1 X X X System fault
X X X 1 X X X X Oxygen signal invalid or no correction
by lambda probe adaption
X X 1 X X X X X Engine starting
X 1 X X X X X X Torque limitation or quantity limitation active
1 X X X X X X X Regeneration exhaust gas treatment
3) Lambda probe plausibility check
001 Current oxygen concentration implausibly high
002 Current oxygen concentration implausibly low
004 Oxygen concentration stationary
008 Plausibility checking enabled
016 Oxygen concentration zero
032 In last time interval no rich operation
4) Lambda probe diagnosis
004 Dynamics of signal too low
008 Cable open circuit
016 Oxygen signal in overrun implausibly low
032 Oxygen signal in overrun implausibly high
064 Oxygen signal at part throttle implausibly low
128 Oxygen signal at part throttle implausibly high

051 Speed recording
1) Engine speed
[rpm]
2) Camshaft speed
[rpm]
3) Start synchronisation
000 Basic initialisation
001 Reset counter
002 Engine standstill or fault
003 Transitional states
004 Plausibility check phase
005 Plausibility check phase
006 Plausibility check phase
008 Plausibility check phase
016 Phase definition
032 Synchronisation phase
033 System positioning
048 Calculation sequences activated --> Start OK
064 System waiting for engine standstill
128 Dynamic plausibility check
4) Injection sequence shut-off status
0 0 0 0 0 0 0 1 Defective external watchdog
0 0 0 0 0 0 1 0 Invalid engine speed
0 0 0 0 0 0 1 1 Run-on
0 0 0 0 0 1 0 0 Shut-off request for time-sync.
shut-off
0 0 0 0 0 1 0 1 Solenoid valve fault
0 0 0 0 0 1 1 0 Overrun
0 0 0 1 0 0 0 0 Minimum post-injection quantity
not reached
0 0 1 0 0 0 0 0 Minimum post-injection duration
not reached
0 1 0 0 0 0 0 0 Deactivation of post-injection via
Speed
1 0 0 0 0 0 0 0 Deactivation of post-injection due to
Error

056 Rail pressure control (from 11.2005)
If not available, see measured value block 110
1) Engine speed
[rpm]
2) Fuel temperature
[°C]
3) Rail pressure control status
0 Ignition on, open-loop control mode
4 Closed-loop control via pressure regulating valve
(normal operating mode)
5 Closed-loop control via solenoid valve
(normal operating mode)
7 Open-loop control (engine is stopped)
15 Closed-loop control via pressure regulating valve and
metering unit
4) Vacant

058 Engine mounting
1) Engine speed
[rpm]
2) Vehicle speed
[km/h]
3) Engine mounting valve, right
0 = Off
1 = On
4) Engine mounting valve, left
0 = Off
1 = On

060 Ancillaries
1) Engine speed
[rpm]
2) Indexed engine torque
[Nm]
3) Engine torque loss
[Nm]
4) Ancillaries
[Nm]

061 Ancillaries
1) Engine torque loss
[Nm]
2) Internal friction torque
[Nm]
3) AC compressor torque
[Nm]
4) Alternator output
[W]

070 Zero quantity calibration ZQC
1) ZQC learning cycle counter 1st calibration pressure
[-]
2) ZQC learning cycle counter 2nd calibration pressure
[-]
3) ZQC learning cycle counter 3rd calibration pressure
[-]
4) Vacant

072 Zero quantity calibration ZQC
1) ZQC cyl. 1 Activation time 1st calibration pressure
[ms]
2) ZQC cyl. 1 Activation time 2nd calibration pressure
[ms]
3) ZQC cyl. 1 Activation time 3rd calibration pressure
[ms]
4) Vacant

073 Zero quantity calibration ZQC
1) ZQC cyl. 2 Activation time 1st calibration pressure
[ms]
2) ZQC cyl. 2 Activation time 2nd calibration pressure
[ms]
3) ZQC cyl. 2 Activation time 3rd calibration pressure
[ms]
4) Vacant

074 Zero quantity calibration ZQC
1) ZQC cyl. 3 Activation time 1st calibration pressure
[ms]
2) ZQC cyl. 3 Activation time 2nd calibration pressure
[ms]
3) ZQC cyl. 3 Activation time 3rd calibration pressure
[ms]
4) Vacant

075 Zero quantity calibration ZQC
1) ZQC cyl. 4 Activation time 1st calibration pressure
[ms]
2) ZQC cyl. 4 Activation time 2nd calibration pressure
[ms]
3) ZQC cyl. 4 Activation time 3rd calibration pressure
[ms]
4) Vacant

076 Zero quantity calibration ZQC
1) ZQC cyl. 5 Activation time 1st calibration pressure
[ms]
2) ZQC cyl. 5 Activation time 2nd calibration pressure
[ms]
3) ZQC cyl. 5 Activation time 3rd calibration pressure
[ms]
4) Vacant

077 Zero quantity calibration ZQC
1) ZQC cyl. 6 Activation time 1st calibration pressure
[ms]
2) ZQC cyl. 6 Activation time 2nd calibration pressure
[ms]
3) ZQC cyl. 6 Activation time 3rd calibration pressure
[ms]
4) Vacant

095 Starter control
1) Terminal 50
0 or 1
2) P/N signal
Only vehicles with automatic gearbox
Signal from selector lever switch
Interlock signal
Only vehicles with manual gearbox
Signal from clutch pedal switch for engine start
0 or 1
3) Vacant
4) Vacant

096 Starter control
1) Terminal 50-back
0 or 1
2) Vacant
3) Starter control shut-off conditions
X X X X X X X 1 Start rejection speed reached
X X X X X X 1 X Road speed threshold
surpassed
X X X X X 1 X X Maximum start time depending on glow period
surpassed
X X X X 1 X X X Maximum start time exceeded
X X X 1 X X X X Terminal 15 deactivated
X X 1 X X X X X Terminal 15 lock
X 1 X X X X X X Terminal 50 or 50-back missing
1 X X X X X X X Starter activated, but engine
speed is 0 rpm
4)Vehicle voltage
[V]

100 Emergency regeneration
Only on vehicles with particulate filter
Note:
Starting emergency regeneration is only possible via Guided Fault Finding
if the <emergency regeneration> test procedure was
entered in the test plan.
1) Engine speed
In emergency regeneration: approx. 1500 rpm
2) Exhaust gas temperature before particulate filter
Regeneration active: above 550 °C
Max. permissible: 820 °C
Abort: 720 °C exceeded for more than 12 sec.
3) Em.regen. current duration
0 ... 255
Total duration: 10 to 40 minutes, depending on loading state
4) Em. regen. Abort detected
0 = Not aborted
1 = Aborted

101 Emergency regeneration
Only on vehicles with particulate filter
Note:
With this measured value block fault causes can be located
if the emergency regeneration was aborted by the engine control unit

1) Em. regen. Enable conditions 1
Before start of emergency regeneration:
0 0 0 0 0 0 0 0 OK, because no emergency regeneration active
After start of emergency regeneration:
1 1 1 1 1 1 1 1 All enable conditions 1 OK
X X X X X X X 1 Minimum waiting time before start of emergency regeneration
with engine running was observed
X X X X X X 1 X Coolant temperature above 70 °C
X X X X X 1 X X Oil temperature above 70 °C
X X X X 1 X X X Ambient air pressure high enough
X X X 1 X X X X Fuel temperature below 70 °C
X X 1 X X X X X Battery voltage adequate
X 1 X X X X X X No clutch pressed
1 X X X X X X X No gear engaged
2) Em. regen. Enable conditions 2
Before start of emergency regeneration:
0 0 0 0 0 0 0 0 OK, because no emergency regeneration active
After start of emergency regeneration:
1 1 1 1 1 1 1 1 All enable conditions 2 OK
X X X X X X X 1 Road speed = 0
X X X X X X 1 X Engine speed in range
X X X X X 1 X X Injection quantity in permissible range
X X X X 1 X X X Accelerator pedal not pressed
X X X 1 X X X X Particulate filter temperature in permissible range
X X 1 X X X X X Pre-catalyst temperature in permissible range
X 1 X X X X X X Soot mass in particulate filter in permissible
Range
1 X X X X X X X No fault memory entries leading to
disabling of emergency regeneration
3) Em. regen. Abort conditions
X X X X X 1 After monitoring time temperatures not
reached
--> Cause: Consumers not switched on,
ambient temperature too cold
X X X X 1 X Temperature for particulate filter exceeded
X X X 1 X X Temperature for pre-catalyst exceeded
X X 1 X X X Abort via enable conditions
--> See zone 1 or 2
X 1 X X X X Abort due to total regeneration time
--> Cause: Consumers not switched on,
ambient temperature too cold
1 X X X X X Abort by diagnostic tester
4) Em. regen. Phase
000 Start emergency regeneration or not activated
001 Warm-up
010 Regeneration active
100 Cool-down

102 Exhaust gas cleaning
Only on vehicles with particulate filter
1) Exhaust gas temperature after pre-catalyst (to 11.2005)
At idle: 90 ... 270 °C
At full throttle: 490 ... 830 °C
1) Exhaust gas temperature before pre-catalyst (from 11.2005)
[°C] Calculated value
2) Exhaust gas temperature before particulate filter
At idle: 70 ... 250 °C
At full throttle: 490 ... 830 °C
3) Particulate filter differential pressure
0 ... 950 mbar
4) Differential pressure offset particulate filter
[mbar]

103 Field regeneration
Only on vehicles with particulate filter
1) Regeneration mode
0 = No field regeneration active
1...100 = Regeneration stages
2) Regeneration request
X X X 1 Counter request active
X X 1 X Request by fuel consumption
X 1 X X Request by operating time
1 X X X Request by distance driven
3) Engine running time since last successful
Regeneration (from 11.2005)
[s]
4) Regeneration disable
X 1 Regeneration disabled
1 X Maximum regeneration time elapsed

104 Particulate filter
Only on vehicles with particulate filter
1) Oil ash
[Ltr]
2) Soot mass calculated
[g]
Displayed value is only valid when the engine has been
running for at least 5 minutes.
3) Soot mass measured
[g]
Notes as field 2)
4) Distance since last regeneration
[km]

107 Particulate filter (from 11.2005)
Only on vehicles with particulate filter
1) Vacant
2) Loading limit 3
[g]
- Value changes according to software part number
- If this limit is exceeded, the engine switches
to emergency running and the fault memory entry
"Particulate filter overloaded" is stored
3) Loading limit 1
[g]
- Value changes according to software part number
- If this limit is exceeded, an attempt is made
to start field regeneration (during driving)
4) Exhaust gas volumetric flow particulate filter
[m^3/h]
Calculated value

110 Rail pressure control (to 11.2005)
If not available, see measured value block 056
1) Engine speed
[rpm]
2) Fuel temperature
[°C]
3) Rail pressure control status
0 Ignition on, open-loop control mode
4 Closed-loop control via pressure regulating valve
(normal operating mode)
5 Closed-loop control via solenoid valve
(normal operating mode)
7 Open-loop control (engine is stopped)
15 Closed-loop control via pressure regulating valve and
metering unit
4) Vacant

125 CAN communication
1) CAN communic. Automatic gearbox
2) CAN communic. ABS/ESP
3) CAN communic. Instrument cluster
4) CAN communic. AC
0 = inactive
1 = active

126 CAN communication
1) CAN communic. ACC
2) Vacant
3) CAN communic. Airbag
4) Vacant
0 = inactive
1 = active

127 CAN communication
1) Vacant
2) Vacant
3) CAN communic. Steering column module
4) Vacant
0 = inactive
1 = active

CAN = Controller Area Network
The CAN bus is a network for local interconnection of
control units.
vag diagnostics, retrofits and general repairs