cruise control inprogrammeren, foutcodes

[a3tdi5d]

Bedankt voor jullie info en tips. Ik ben er helaas na 6 maanden nog steeds er niet in geslaag om mijn cruise control aan de praat te krijgen.
Ik heb het wel via de motermagement en de steering modele kunnen activeren. Dit andere onderdeel wat hieronder staat beschreven daar kom ik helaas niet uit

zou eventueel iemand hiermee kunnen helpen?



Audi_A4_(8E)_Steering_Wheel

Coding

* 0?xxx: Steering Wheel
o 0 = Standard (without Multifunction)
o 1 = 3-Spoke Steering Wheel (Sport Steering Wheel)
o 2 = Multifunction Steering Wheel with Radio Control
o 3 = Multifunction Steering Wheel with Radio/Telephone Control
o 4 = Multifunction Steering Wheel with Radio/Telephone/Voice Control
o 5 = Multifunction Steering Wheel with Radio/Voice Control
* 0x?xx: Options
o +1 = Tiptronic
* 0xx?x: Board Computer & Cruise Control
o 0 = Board Computer & Cruise Control not installed
o 1 = Board Computer installed
o 2 = Cruise Control installed
o 4 = Board Computer & Cruise Control installed
* 0xxx?: Rear Wiper (Chassis)
o 1 = Rear Wiper not installed (Sedan/Cabriolet)
o 2 = Rear Wiper installed (Avant)


Adaptation
Channel 081: Vehicle Data Learning

To start the process for vehicle data (VIN) learning, enter/save 00111 as new value.



Audi A4 (8E) Brake Electronics (Bosch 5.7)
From Ross-Tech Wiki



All of the following procedures must be performed in order, WITHOUT shutting off the ignition or exiting out of the ABS controller.
Contents
[hide]

* 1 Login
* 2 Coding
* 3 Basic Setting
o 3.1 Steering Angle Sensor (G85) Calibration

Login

Note #1: After Login has been carried out you need to recode the control module.
Note #2: Special Login 09399 is used for BFB Engine with 1LT Brakes and Multitronic.
Note #3: The PR codes ( such as 1LJ ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker http://www.ross-tech.net/vag-com/mis...s/PR-Codes.png

* 0?xxx: Chassis
o 9 = Audi A4
* 0x?xx: Brakes
o 2 = Brembo 17" (PR-1LJ)
o 3 = FN3 16" (PR-1LT/1LF)
o 4 = HP2 16" (PR-1LX)
o 4 = FNR 16" (PR-1LA/1LG)
o 5 = FN3 15" (PR-1LB/1LE)
o 6 = C54 (PR-1LZ)
* 0xx?x: Engine
o 5 = 4/6 Cyl. Diesel
o 7 = 4/5 Cyl. Gasoline
o 9 = 6/8 Cyl. Gasoline
* 0xxx?: Transmission
o 5 = Manual
o 7 = Automatic (5HP19, 5HP24, AG4, AG5)
o 9 = Multitronic (01J, CVT)

Coding

Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out.
Note #3: Special Coding 04499 is used for BFB Engine with 1LT Brakes and Multitronic.
Note #4: The PR codes ( such as 1LJ ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker http://www.ross-tech.net/vag-com/mis...s/PR-Codes.png

* 0?xxx: Chassis
o 4 = Audi A4
* 0x?xx: Brakes
o 1 = C54 (PR-1LZ)
o 2 = FN3 15" (PR-1LB/1LE)
o 3 = HP2 16" (PR-1LX)
o 3 = FNR 16" (PR-1LG)
o 4 = FN3 16" (PR-1LT/1LF)
o 5 = Brembo 17" (PR-1LJ)
* 0xx?x: Engine
o 5 = 4/6 Cyl. Diesel
o 7 = 4/5 Cyl. Gasoline
o 9 = 6/8 Cyl. Gasoline
* 0xxx?: Transmission
o 5 = Manual
o 7 = Automatic (5HP19, 5HP24, AG4, AG5)
o 9 = Multitronic (01J, CVT)

Basic Setting
Steering Angle Sensor (G85) Calibration

Note: Make sure the above Login and Coding have been done successfully before proceeding.

[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Turn steering wheel at least 30 ° left and back straight ahead.
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]

[Login - 11]
Enter 40168
[Do It!]

[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]

[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]

[Close Controller, Go Back - 06]
Retrieved from "http://wiki.ross-tech.com/wiki/index.php/Audi_A4_(8E)_Brake_Electronics_(Bosch_5.7)"
geactiveerd en via de

[dianick]

Waar woon je? PM me maar!
Ik wil best een poging wagen, geen garantie echter

[remcomb]

Als ik dit zo lees, kun je beter geen extra hardware zelf toevoegen. Als je ABS, ESP e.d. gaan uitvallen.... Ik zou daar niet aan beginnen. Het geeft wel aan hoe kwetsbaar het totale systeem is. Ongeveer alles hangt van foutloze software af :S/.

[The Wale]

Ik heb vandaag cruise control in mijn A3 ingebouwd.
Ik heb alles het stuur ook goed terug gezet, de streepjes stonden zoals ze waren bij demontage.
Alleen staat het stuur nu een klein beetje scheef, is uitlijnen hier de beste oplossing?

Verder heb ik ook 2 foutmeldingen gekregen, maar die zou ik dus opnieuw moeten inleren.
Het gaat om de volgende fouten:

Address 44: Steering Assist        Labels: 1Kx-909-14x-44.clb
   Part No: 1K1 909 144 L
   Component: EPS_ZFLS Kl.078 H07 1806  
   Shop #: WSC 02069 000 90108
   VCID: 346D1E6F2EAB

2 Faults Found:
02546 - Steering Limit Stop 
            005 - No or Incorrect Basic Setting / Adaptation
             Freeze Frame:
                    Mileage: 76120 km
                    Temperature: 26.0°C
                    Voltage: 12.00 V
                    Voltage: 11.80 V

00778 - Steering Angle Sensor (G85) 
            005 - No or Incorrect Basic Setting / Adaptation
             Freeze Frame:

Edit: Alles is ondertussen in orde ,dankzij de uitleg op gerritspeek en rosstech.